How To Repair Broken Fishing Rod

Download Article

Download Article

Modern fishing rods don't break easily, but they can be fixed easily with a few simple tools you may have at home. If your rod snapped, y'all can mend it together with a fiberglass pole and epoxy to hide the break. When ane of the guides breaks, you tin remove information technology and wrap a new one in its place. Y'all can change rod tips if they snap or break as well. With a little scrap of work, y'all can set your rod so it's every bit proficient equally new!

1. ane

   Sand or cut the cleaved ends of the rod so they're affluent. Utilize 180- or 220-grit sandpaper to smooth the ends so they fit together easily if the rod has a clean break. If your fishing rod has a jagged edge, so use a pair of scissors to cut the sharp edges off of the end of the rod and so the pieces are flush. After y'all brand your cut, employ sandpaper to smoothen out the edges and roughen upwardly the surface.^[ane]

   • Jagged edges are weaker and are more probable to interruption again than edges that are flush with one another.

2. 2

   Measure the circumference of the rod. Use a flexible tape mensurate and wrap it around the broken end of your angling rod. Then measure the circumference on the other piece of your fishing rod to meet if it's skinnier. Write downwardly your measurements so y'all know what pole size you need for fixing your rod.^[ii]

   • You can also mensurate the diameter of the rod on both of the broken ends if you don't have a flexible measuring record.

   Advertisement

3. 3

   Cut a piece of fiberglass pole so it's about 12 in (30 cm) long. Get a fiberglass pole that has a circumference that's most ¹⁄₈ – ^ane⁄₄ inch (0.32–0.64 cm) smaller than your fishing rod. Use a hacksaw to cut out a 12 in (thirty cm) section of the pole so it tin can fit inside your fishing rod and support the rod without breaking.^[3]

   • Y'all can buy fiberglass poles from your local hardware store. Information technology doesn't matter what color you use since it will fit within of the rod.
   • If your fishing rod isn't hollow, so using a fiberglass pole won't work. You can either attempt to record your rod back together or get a new i.

   Tip: You can also cut a department off of an old angling pole that you don't use anymore if you don't have a fiberglass rod.

4. 4

   Slide the fiberglass pole into one side of the angling rod. Concur your rod horizontally and so you can position the fiberglass pole in the rod without it sliding too far. Push button ane end of the fiberglass pole into the terminate of the rod with the handle. Proceed sliding the pole into the line-fishing rod until at that place'south half dozen inches (15 cm) sticking out from the end.^[4]

   • If the pole doesn't fit snugly inside the fishing rod, then wrap the pole with duct or masking record to make it thicker.

5. five

   Use 2-part epoxy to the exposed side of the fiberglass pole. Open your 2-part epoxy and pour it into a basin. Use a paintbrush to spread a thin layer of the epoxy on the exposed end of the fiberglass pole. Once the ii-part epoxy is mixed, work quickly so information technology doesn't dry or set earlier you put your rod back together.^[v]

   • You tin can purchase ii-part epoxy from any hardware or craft store.

6. 6

   Slide the other office of the rod onto the fiberglass and let it dry. Slowly push the other terminate of your rod onto the exposed terminate of the fiberglass pole. Make sure the guides on the pole line upward with one another so your line doesn't get tangled when y'all try using your pole once again. Button the 2 pieces of the rod together then they're affluent. Let the epoxy gear up overnight then it firmly adheres to the rod.^{[half dozen]}

   • The epoxy doesn't set right away, then you lot tin still rotate or motion the rod pieces once y'all slide them together.
   • If any epoxy comes out of the joint while you're sliding the pieces together, wet your finger and smooth out the epoxy so it isn't every bit visible.
   • Wrap a layer of electrical tape around the seam if you want an additional layer of security.

Ad

1. i

   Cut the tape or thread effectually the cleaved guide with a razor blade. Use a straight razor blade or a craft knife to remove whatever threading that may be surrounding the rod guide. If it'south difficult to remove using merely a blade, and then try heating the area for three-4 seconds with a lighter to loosen any of the adhesives. Skin off the record and unwind the threading until the sometime, broken guide comes off of the rod.^[7]

   • Rod guides are the circular metallic pieces along the length of the rod that help proceed your line straight.
   • Be careful non to heat the rod for also long since it could cause damage to information technology.
   • Don't cutting into the rod with your razor, or else yous could damage it and make it weaker.

2. ii

   Sand the rod and foot of the new guide to get better adhesion. Use 120- or 220-dust sandpaper to go rid of whatever leftover agglutinative and to add tooth to the rod. Rub all the way around the rod on the spot where you want to place the new guide. Then, utilize your sandpaper on the foot of the guide, which is the flat function that rests confronting the fishing rod.^[eight]

   • You lot can purchase new line-fishing guides at sporting skillful stores. Make sure the new guide is the same size and fashion as the other guides on your fishing rod or else your line may snag or get tangled.

3. 3

   Tape the new guide onto the rod so it's aligned. Press the foot of the new guide onto the rod so it's in line with the other guides. Rip off a thin slice of masking tape and wrap it around the pes then information technology's held in place. That fashion, yous don't need to keep holding it in place while you wrap it.^[9]

   • You can as well utilize super glue, just information technology will be hard to motility or readjust once the gum is ready.

4. iv

   Wrap the foot of the guide with thread to hold information technology in place. Whatever type of thread volition work for wrapping your guide onto the rod. Loop your threading effectually the rod then it'southward ¹⁄_two – ^three⁄₄ inch (ane.iii–ane.9 cm) from the guide's foot on the side closest to the handle. Maintain tension on the loop and get-go tightly winding the thread around the rod. Brand sure the thread doesn't overlap with loops you've already made and that they are flush with one another.^[10]

   • Take the piece of record off of the foot you've wrapped everything beneath information technology.

   Tip: Use a thread that matches the color of your rod if you lot want it to blend in.

5. 5

   Place a looped piece of thread over the wrap when there's ¹⁄₈  in (0.32 cm) left. When your wrapping is ¹⁄₈ inch (0.32 cm) from the circular office of the guide, finish winding the thread around the pole. Cut a separate piece of thread so it's about 6 inches (15 cm) long and fold it in one-half to course a loop. Lay the second piece of thread on top of your wrapping so the loop sticks out near your guide.^[eleven]

   • If you don't take any other thread, you tin also apply a sparse fishing line instead.

6. 6

   Wrap the terminal ^ane⁄₈  in (0.32 cm) over the second piece of thread. Once the looped piece of thread is on meridian of the wrapping, continue spinning your thread effectually the foot of the guide. Continue wrapping the final ¹⁄_eight inch (0.32 cm) of the guide then the middle of the looped piece is held against the rod.^[12]

7. 7

   Feed the thread through the looped slice and pull it tight. One time you accomplish the cease of your wrapping, cut the terminate of the thread you used to wrap and pull it through the middle of the loop. Pull the other stop of the looped slice down and abroad from the guide to pull the thread underneath the wrapping. This way, the wrapping is secured to the rod without having to necktie a knot.^[xiii]

   • If y'all don't desire to utilise a looped piece of thread, you can likewise try tying a knot in the threading, merely it may non be as strong and it could be more difficult.

8. eight

   Pigment ii-part epoxy onto the thread and let it dry. Mix the ii parts of the epoxy in a pocket-size dish with a paintbrush until they are thoroughly combined. Pigment a thin layer of the epoxy over your threading so information technology hardens and stays in identify. Keep the rod horizontal and allow information technology dry overnight before you try using your rod again.^[xiv]

   • Work quickly with the epoxy since it volition rapidly start to dry out and harden in one case you lot mix information technology.

Ad

1. 1

   Heat the tip top of your fishing rod with a lighter to loosen the adhesive. Set the rod horizontal then you can easily reach the tip. Hold a lighter underneath the tip height of the rod, which is the ringed piece at the end of the rod, and heat it upwards for 4-5 seconds at a fourth dimension. Once it's heated, try pulling it off with a pair of pliers or past hand. If it doesn't come off hands, effort heating it for another few seconds.^[15]

   • Heating the tip top helps loosen the adhesive holding it in place and then it'southward easier to remove.
   • If the tip snapped off of your rod, then yous tin remove the old tip top from the broken slice or you lot tin skip this step.

2. 2

   Shine the tip of the rod with sandpaper to remove any shards. Rub the exposed tip of the rod with 120- or 220-dust sandpaper to smoothen it out. Rotate the rod effectually the sandpaper until the tip is polish and flush. It's okay if there are small abrasion marks on the rod tip since it will accept amend adhesion to the new tip summit.^[16]

   Tip: If sandpaper isn't enough to remove the shards on the end of your fishing rod, and then carefully cutting off the ends with a pair of scissors.

3. three

   Cut pieces of rod cement into strips that fit inside your new tip elevation. Rod cement is an adhesive that comes in a solid cake and is used for angling rods to hold guides and tips in place. Use a razor or craft knife to cut out small strips of the rod cement so they fit inside the hollow chamber on your rod tip peak.^[17]

   • You lot can buy rod cement and new tip tops from your local sporting goods shop or online.

4. four

   Melt the rod cement inside the tip top with your lighter. Concord the new tip top with a pair of pliers and put the pieces of rod cement in the hollow tube at the terminate of it. Use your lighter to heat the rod cement for 4-five seconds and cook it and then you can attach it to your rod. Once the rod cement is melted, piece of work quickly and then information technology doesn't solidify again.^[18]

5. v

   Slide the tip top onto your rod so it lines upwards with the guides and let it dry. While the cement is notwithstanding hot, slide it onto the tip of your rod and rotate it so the ring is in line with the other guides. Wipe away any excess rod cement with a piece of paper towel and let information technology set for at least 1-2 hours. Once the cement is dry, your rod is prepare to use!^[19]

   • If you need to adapt or reposition the tip top after the cement is dry, then rut information technology once again for iii-4 seconds with your lighter.

Advertisement

Add New Question

• Question

  Where do I purchase epoxy resin glue?

  

  At any habitation improvement or hardware store.

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertizement

Video

• If y'all need to fix a snapped rod in an emergency, overlap the pieces by 6 inches (xv cm) and tape them together tightly.^[xx]

• Accept your rod to a fishing supply store or a repair person if you take problem fixing it on your own.

Thanks for submitting a tip for review!

Advertisement

• Don't concord a flame against your rod longer than a few seconds or else yous could permanently damage the rod.

• Be careful while working with razor blades so y'all don't accidentally cut yourself.

Advertisement

Things You lot'll Need

• Scissors
• Sandpaper
• Tape measure
• Fiberglass pole
• Hacksaw
• 2-role epoxy
• Bowl
• Paintbrush
• Electrical tape (optional)

• Razor bract
• Lighter
• Sandpaper
• Masking record
• Rod guides
• Thread
• 2-office epoxy
• Dish
• Paintbrush

• Lighter
• Pliers
• Sandpaper
• Rod cement
• Craft knife
• Rod tip top

About This Article

Article Summary Ten

To prepare a snapped fishing rod, endeavour using a fiberglass pole and some epoxy. First, sand the snapped edges to make them flush. Smooth edges are stronger and less likely to break. Cut a 12 inch long slice of fiberglass pole using a hacksaw. Slide 1 end of the pole into your fishing rod until in that location are 6 inches sticking out. In one case the fiberglass pole fits snugly into the rod, apply epoxy to the exposed end using a paintbrush. Connect the 2d half of the broken rod to the fiberglass pole and allow the epoxy set. To replace the rod guide, first, remove any threading from around the guide using a craft knife. Align the new guide onto the rod and use tape to hold it in place. Wrap the new thread over the guide and then cover it in epoxy to set it. For more than ideas on fixing a broken line-fishing rod, like how to modify a rod tip, read on.

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 230,650 times.

Did this commodity aid you?

Source: https://www.wikihow.com/Fix-a-Broken-Fishing-Rod

Share this post